Toyota Funcargo Wiper Blade Sizes: 1999-2005 Replacement Guide

Published: September 11, 2026

Quick Answer: Toyota Funcargo Wiper Blade Sizes

Toyota Funcargo wiper blade sizes are 600 mm (24 in) on the driver side, 400 mm (16 in) on the passenger side, and 350 mm (14 in) at the rear. Most 1999–2005 Funcargo models use a U-hook (J-hook) connector, but confirm the fitting on your own vehicle before buying.

Key takeaways:

• Driver side: 600 mm (24 in)
• Passenger side: 400 mm (16 in)
• Rear: 350 mm (14 in)
• Connector: U-hook (J-hook) 9×3 mm or 9×4 mm is most common; some trims use pin or side-lock
• Replacement interval: Every 6–12 months, or sooner if the blades streak or chatter
• Time required: 10–15 minutes for all three blades
• Tools needed: New blades, clean rag, glass cleaner, optional 10 mm socket for the rear arm

Why Getting the Right Size Matters on a Funcargo

The Toyota Funcargo is a compact MPV built from 1999 to 2005 and shares its basic platform architecture with the Vitz and first-generation Yaris. That lineage is helpful for parts hunting, but it does not guarantee identical wiper fitment — the Funcargo's windshield rake and cowl are its own, and the rear glass is shaped differently from most hatchbacks of the era.

A wiper blade that is too long does not just look wrong. It can strike the A-pillar or the cowl trim at the top of its stroke, which bends the arm, chips the paint, and eventually strips the splines on the pivot. A blade that is too short leaves a blind strip of uncleared glass right in your line of sight — a real problem in monsoon rain or early-morning fog.

This guide covers exact Toyota Funcargo wiper blade sizes, how to verify the connector on your specific vehicle, OEM versus aftermarket options, a full step-by-step Toyota Funcargo wiper replacement procedure, and troubleshooting for the problems these cars commonly develop as they age.

Toyota Funcargo Wiper Blade Sizes by Position

Front Wiper Blade Sizes

• Driver side: 600 mm (24 in)
• Passenger side: 400 mm (16 in)
• Blade types available: conventional (framed), beam (flat), and hybrid
• Connector: U-hook (J-hook) in 9×3 mm or 9×4 mm is by far the most common. A small number of trims and later-model replacements use a pin or side-lock fitting, so inspect the arm before ordering.

The asymmetric pairing — a long 600 mm blade on the driver's side and a short 400 mm blade on the passenger side — is typical of Japanese market compact cars of this era. It maximizes the swept area on the driver's side without overloading the smaller passenger-side linkage.

Rear Wiper Blade Size

• Rear: 350 mm (14 in)
• Connector: Usually U-hook; some early or late builds use a pin-style fitting
• Note: A minority of aftermarket catalogs list 300 mm (12 in) for the rear. Measure your old blade before you commit.

Size Verification Chart

How to Confirm the Exact Sizes for Your Funcargo

Even within the 1999–2005 production window, Toyota made running changes to trim and equipment. Rather than guessing, use one of these methods:

1. Check the owner's manual. The maintenance section often lists blade lengths in the specifications table.
2. Measure the old blade. Run a tape measure along the rubber strip only — not the metal frame or the connector. Rubber length is what the catalog number refers to.
3. Use your VIN. A Toyota dealer parts counter can pull the exact original part number for your chassis code.
4. Cross-check a fitment guide. Denso, Bosch, Trico, and PIAA all publish vehicle fitment databases that let you search by model, year, and engine.
5. Compare at the counter. If you can, bring the old blade with you. Laying the new blade alongside the old one takes five seconds and prevents a return trip.

If you are comparing across Toyota's small-car family, note that front sizes often differ between the Funcargo and the Yaris or Vitz, so don't assume interchangeability. For a closer look at how these sizes vary across models, see our [link to related guide on Toyota Yaris wiper blade sizes].

OEM vs Aftermarket Wiper Blade Options

Toyota OEM Blades

Genuine Toyota blades give you an exact-fit guarantee straight from the factory parts catalog. They are built to the same durability standard as the originals and, on these cars, usually come as a blade assembly with a serviceable rubber refill.

The trade-offs are real, though. OEM blades typically cost more than aftermarket equivalents, and outside Japan, availability for a 20-year-old JDM model can be spotty. In my experience, dealers can usually order them, but you may wait several days for delivery.

Recommended Aftermarket Brands

Blade type comparison:

• Conventional (framed): Cheapest, widely available, works well in light rain. The exposed frame can pack with snow and ice.
• Beam (flat): No exposed frame, so it resists snow buildup and maintains even pressure across the glass. Best choice for cold climates and highway driving.
• Hybrid: A conventional-style body with a partial cover. A reasonable middle ground.

Refill or full blade? Genuine Toyota blades on these cars often accept a rubber refill, which costs a fraction of a new assembly and takes about two minutes per blade. Most aftermarket blades are sealed units and must be replaced whole. If your Funcargo still has its original-style blades, refills are the cheapest path — check out our [link to related guide on wiper blade refills vs full replacement] for a full comparison.

Buying Tips

• Match both the length and the connector type — a 24-inch blade with the wrong fitting is useless.
• For beam blades, confirm the part number is listed for your specific model year; curvature varies.
• Never go oversized. A 650 mm blade where a 600 mm belongs will foul the A-pillar.
• Match the blade to your climate: silicone holds up better in intense heat and UV, while beam blades shed snow more effectively.

Tools and Materials You'll Need

Gather everything before you start so you are not hunting for a socket with the arm raised:

• New wiper blades: 600 mm driver, 400 mm passenger, 350 mm rear
• Clean rag or microfiber towel
• Glass cleaner or isopropyl alcohol
• Tape measure (for verification)
• Flathead screwdriver (to release stubborn connectors)
• 10 mm wrench or socket (for the rear wiper arm nut, if removal is needed)
• Painter's tape or a thick towel (to protect the glass)
• Gloves (optional)

Step-by-Step Toyota Funcargo Wiper Replacement

Preparation

1. Park on a level surface and set the parking brake. Turn the ignition off and remove the key.
2. Let the wiper arms rest in their normal parked position against the glass.
3. Lift the wiper arm away from the windshield until it locks upright. On most Funcargo arms, a friction detent holds it there.
4. Lay a folded towel or strip of painter's tape on the glass beneath the arm. If the arm slips out of its detent, it snaps down hard enough to crack a windshield.

Front Wiper Blade Replacement (Driver and Passenger)

U-hook (J-hook) connector — the most common setup:

1. Lift the wiper arm until it locks in the upright position.
2. Press the release tab on the connector where the blade meets the arm. You will feel a small click.
3. Slide the blade down and off the hook. Rotate it slightly as you pull and it will come free.
4. Compare the new blade to the old one. Confirm the length and that the connector matches before you install anything.
5. Slide the new blade onto the hook and push upward until it clicks into the locked position. Tug it gently to confirm — it should not slide off.
6. Gently lower the arm back onto the glass. Never let it drop.
7. Repeat for the other side, then run through steps 1–6 for the passenger blade.

Pin or side-lock connector (if equipped):

1. Lift the wiper arm to the locked position.
2. Depress the locking pin or slide the release tab outward, depending on the design.
3. Pull the blade straight off the arm — no rotation needed on most pin fittings.
4. Attach the new blade and press until the lock fully engages. You should hear or feel a positive click.
5. Lower the arm slowly and test the lock by rocking the blade lightly.

Rear Wiper Blade Replacement

1. Lift the rear wiper arm away from the back glass and hold it upright.
2. Identify the connector. Most Funcargo rear arms use a U-hook; some use a pin.
3. Release the tab and slide the old blade off the hook.
4. Install the new 350 mm blade and confirm it locks in place.
5. Lower the arm gently onto the glass.
6. If the arm itself needs removal: pry off the plastic nut cover, unscrew the 10 mm retaining nut, and pull the arm straight off the splined shaft. Clean the splines, align the new arm at its parked position, and reinstall.

On the arm nut torque: Toyota's service data for small wiper arm nuts generally falls in the 13–18 Nm (roughly 10–13 lb-ft) range, but confirm the exact figure for your model year in the service manual. Overtightening can distort the arm; undertightening lets it slip on the splines and stop parking correctly.

Testing and Final Checks

1. Spray washer fluid across the windshield.
2. Cycle the wipers through low, high, and intermittent speeds.
3. Watch the sweep pattern. Look for streaks, chatter, or areas the blade skips.
4. Confirm the blades park correctly at the bottom of the windshield and do not overlap each other.
5. Re-tighten the rear arm nut if you removed the arm, then test the rear wiper separately.
6. Remove the protective towel from the glass.

Troubleshooting Common Toyota Funcargo Wiper Issues

Two decades of UV exposure, road grit, and dried-out rubber take a toll on these small wiper linkages. Here is how to diagnose the most frequent complaints.

Streaking or Smearing

1. Clean the windshield and wipe the blade edge with glass cleaner or isopropyl alcohol.
2. Inspect the rubber for cracks, hardening, or missing chunks.
3. Replace the blade if the rubber is worn or the edge is no longer square.
4. Check the arm for bends — a twisted arm cannot apply even pressure.
5. Verify you installed the correct length: 600 mm driver, 400 mm passenger.

Chatter or Juddering

1. Clean the glass with isopropyl alcohol to strip wax, silicone, and traffic film.
2. Inspect the blade for damage or a hardened edge.
3. Switch to a beam blade if you are running a conventional one — beam designs distribute pressure more evenly.
4. Check the arm spring tension. A weak spring lets the blade skip across the glass.
5. Adjust the arm angle if the blade is leaning too far forward or backward.

Squeaking

1. Clean the blade and glass thoroughly.
2. Apply a thin film of silicone grease to the blade edge as a temporary quieting measure.
3. Replace the blade if the noise returns.
4. Inspect the arm angle and replace the arm if it is bent.

Missed Areas or Uneven Wipe

1. Verify blade length and connector type.
2. Clear any ice or snow packed under the blade.
3. Replace the blade — a torn or wavy edge will always miss spots.
4. Check the arm for damage or a loose pivot.

Wiper Arm Hits the A-Pillar or Cowl

1. Measure the blade. It should be 600 mm on the driver's side and 400 mm on the passenger side.
2. Reposition the arm on the splines so it parks lower or higher as needed.
3. Replace the arm if it is bent — straightening a wiper arm rarely holds.

Rear Wiper Not Parking or Not Moving

1. Check the fuse box for a blown rear wiper fuse.
2. Tighten the arm nut — a loose nut is the most common cause of a wiper that sweeps but doesn't park.
3. Inspect the splines on the shaft and inside the arm. Stripped splines require a new arm.
4. Test the motor with a multimeter or a known-good power source; replace if it has failed.

Washer Nozzle Problems

1. Refill the washer reservoir with proper fluid.
2. Clear a clogged nozzle with a fine pin.
3. Check the hose for kinks or disconnection.
4. Test the pump; replace it if it does not hum when activated.

Maintenance Tips and Replacement Frequency

Wiper blades are consumables, and the Funcargo's small blades work hard for their size.

• Replace every 6–12 months. If you live somewhere with intense sun, heavy monsoon rain, or freezing winters, lean toward the 6-month end.
• Wipe the blades monthly with an alcohol wipe. Thirty seconds of maintenance adds months of service life.
• Use proper washer fluid. Plain water encourages mold growth in the reservoir and does not clean glass well.
• Lift the blades off the glass before a freeze so they do not bond to the windshield.
• Never dry-wipe. Running wipers on a dry windshield shreds the rubber edge.
• Park the blades in a service position during heavy snow if your routine allows it.

Frequently Asked Questions

What size wiper blades does a Toyota Funcargo use?

The driver side takes 600 mm (24 in), the passenger side takes 400 mm (16 in), and the rear takes 350 mm (14 in). Confirm with your VIN or a fitment guide before purchasing, since trim and year variations exist.

Are Toyota Funcargo wiper blades the same as Toyota Yaris or Vitz?

Not necessarily. The Funcargo shares a platform family with the Vitz and Yaris, but front blade lengths and connector types can differ. Always verify against your specific model and year rather than assuming interchangeability.

Can I use larger wiper blades on my Funcargo?

It is not recommended. Oversized blades can strike the A-pillar or cowl at the top of the sweep, which bends the arm and can strip the pivot splines over time. Stick to 600 mm and 400 mm up front.

How do I know if my Funcargo uses a U-hook or pin connector?

Look at the end of the wiper arm. A U-hook has a J-shaped metal hook that curves back on itself; a pin connector has a small cylindrical pin with a locking clip. If you cannot tell by looking, check the owner's manual or bring the old blade to the parts counter.

What is the rear wiper blade size for a Toyota Funcargo?

It is commonly 350 mm (14 in), though a few sources list 300 mm (12 in). Measure the rubber strip on your existing blade to be certain — the rear fitting is the one most often mis-ordered.

How often should I replace wiper blades?

Every 6 to 12 months under normal use, or immediately if you notice streaking, chattering, or missed patches. Extreme heat, cold, or dusty conditions shorten that interval considerably.

Conclusion

Toyota Funcargo wiper blade sizes are straightforward once you know them: 600 mm (24 in) driver, 400 mm (16 in) passenger, and 350 mm (14 in) rear. The part that trips people up is the connector, so inspect the arm or check your VIN before you buy.

Both front blades take about ten minutes to swap, and the rear adds five more. Do it on a level surface with a towel protecting the glass, test the sweep pattern afterward, and you will have clean, quiet, chatter-free visibility for the next six to twelve months.

Worn blades are one of the cheapest safety upgrades you can make to any vehicle, and on a car as compact and exposed as the Funcargo, they matter more than most drivers realize. Check yours today — if the rubber is hard, cracked, or leaving streaks, replace it. For genuine parts, your local Toyota dealer is the safest source; for everything else, a reputable wiper brand's fitment guide will steer you right.

Additional Resources

• Toyota owner's manual and dealer parts department for VIN-based fitment
• Denso wiper blade catalog and fitment guide
• Bosch and Trico aftermarket fitment databases
• Toyota Funcargo owner communities and forums for model-specific tips
• Our [link to related guide on wiper blade connector types] for help identifying your fitting

About the Author: Erwin Salarda is an Automotive Service Equipment Technician based in the Philippines, specializing in computerized automotive diagnostic equipment such as OBD scanners and wheel alignment systems. Since 2012, he has been actively providing technical support, equipment installation, troubleshooting, after-sales service, and hands-on training for automotive service equipment used by workshops and automotive professionals.

He has received specialized training from international suppliers and manufacturers, including Launch X431 in Shenzhen, China, Lawrence Engineering Company in Guangzhou, China, and 3Excel Wheel Alignment Company in Shenzhen, China. Through these trainings, he developed advanced expertise in automotive diagnostics, calibration, wheel alignment systems, and computerized automotive service technologies.

Erwin Salarda provides professional after-sales support and technical training for automotive diagnostic and wheel alignment equipment, helping clients maximize the performance and proper use of their tools and systems. His experience covers equipment setup, software updates, calibration procedures, troubleshooting, and operational guidance for automotive workshops and service centers.

With more than a decade of experience in the automotive equipment industry, Erwin Salarda continues to support automotive businesses by delivering reliable technical expertise and practical training solutions.

For inquiries and equipment purchases, please visit https://carlifterph.com/

Related Posts

• Toyota Funcargo Engine Air Filter Replacement Guide (DIY)
• Toyota Funcargo Cabin Air Filter Replacement Guide (10-20 Min)
• Toyota Funcargo Spark Plug Replacement: Interval, Symptoms & Cost
• Toyota Funcargo Coolant Type, Capacity & Replacement Interval
• Toyota Funcargo Service Costs: Annual Maintenance Budget Explained