Mechanic Wiki: How to Reset TPMS on Hyundai i10 (All Years)

Learn how to reset the TPMS light on your Hyundai i10. Step-by-step instructions for automatic reset, manual button (2010–2013), and cluster menu (2014+).

Published: June 27, 2026

Quick Answer: The TPMS (Tire Pressure Monitoring System) on a Hyundai i10 resets automatically after you inflate all tires to the correct pressure and drive above 40 km/h (25 mph) for 10–20 minutes. If the warning light remains on, use the manual reset button located under the steering column or inside the glovebox (2010–2013 models) or the instrument cluster menu (2014–present). Follow the specific method for your model year to turn off the TPMS light.

Why Your Hyundai i10 TPMS Light Might Stay On

A glowing or blinking TPMS light can be frustrating. Before reaching for a reset tool, it helps to understand what’s triggering the warning. Here are the most common reasons:

Low tire pressure – This is by far the most frequent cause. Even a small drop from the recommended pressure (listed on the driver’s door jamb sticker) will turn the light on.
Faulty TPMS sensor – Each tire has a sensor powered by a small battery. These batteries typically last 5–7 years. Once dead, the sensor stops transmitting data.
Sensor not re-paired – After a tire rotation or replacement, the system may lose communication with the new sensor location. A relearn procedure is needed.
Temperature changes – Colder weather can drop tire pressure by 1–2 PSI, enough to trigger the light. Inflating to the cold pressure usually fixes it.
System fault – A problem with the TPMS module or wiring can cause the light to stay on. This requires professional diagnosis with a scan tool.

Understanding the cause will save you time. If the light came on after a sudden temperature drop, simply inflating the tires may turn it off automatically. If it blinks for 60–90 seconds then stays solid, it likely indicates a sensor fault.

Step‑by‑Step TPMS Reset Methods for Hyundai i10

The correct reset method depends on your i10’s model year. Here are the four most common procedures.

Method 1: Automatic Reset (All Years)

Every Hyundai i10 has a built-in automatic relearn feature. This is the simplest method – no button pressing required.

Park the car on a level surface and turn off the engine.
Check all four tires with a reliable gauge. Inflate each to the pressure printed on the driver’s door jamb sticker. (Common pressure for i10 is 33 PSI front and rear, but always verify.)
Start the engine and drive the car above 40 km/h (25 mph) for at least 10 minutes. The system will detect the new pressures and turn off the warning light.
If the light remains on after 20 minutes of highway driving, proceed to manual reset.

Method 2: Manual Reset Using the TPMS Button (2010–2013 Models)

For i10 models built between 2010 and 2013, there is a dedicated reset button.

Locate the TPMS reset button. It is usually a small square button marked “SET” or with a tire‑and‑exclamation icon. Common locations: under the steering column, near the hood release, or inside the glovebox.
Turn the ignition to the ON position (do not start the engine).
Press and hold the reset button. Hold it until the TPMS light blinks three times, then release.
Start the engine. Drive the car at 40 km/h for a few minutes. The light should turn off.

Method 3: Manual Reset via Instrument Cluster (2014–Present Models)

Newer Hyundai i10 models (2014 onward) do not have a physical reset button. Instead, you reset through the dashboard menu.

Press the TRIP button on the steering wheel to cycle through the display options.
Scroll to the User Settings menu.
Use the scroll wheel to find “TPMS” or “Tire Pressure Monitoring.”
Press and hold the OK button until the TPMS indicator blinks three times.
Exit the menu and drive above 40 km/h for a few minutes to complete the reset.

Method 4: Using a TPMS Relearn Tool (For Sensor Replacement or Rotation)

If you replaced a sensor or rotated tires, a dedicated TPMS relearn tool may be necessary. These tools are available at auto parts stores for around $30–$50.

Turn the ignition to the ON position (engine off).
Follow the tool manufacturer’s instructions. Typically, you place the tool against the tire sidewall near the valve stem, in a specific order (e.g., LF, RF, RR, LR).
The horn will chirp or the lights will flash to confirm each sensor has been learned.
Once all sensors are learned, turn off the ignition, then start the engine and drive. The TPMS light should be off.

Common Troubleshooting Tips

Problem	Likely Cause	Solution
Light blinks 60–90 seconds then stays on	System malfunction or sensor fault	Have sensors checked with a TPMS scanner
Light stays on after driving	Pressure not set correctly	Double‑check pressures with a gauge while tires are cold
Light comes back after reset	Slow leak or temperature drop	Inflate 2–3 PSI above sticker pressure; inspect tires for punctures
No TPMS button found	Model year without manual reset	Only automatic reset works – drive longer at higher speed
“TPMS” message on dashboard	Sensor battery low or dead	Sensor replacement needed (usually $40–$80 each)

When to Seek Professional Help

The TPMS light remains on after three reset attempts and correct tire pressures.
You have aftermarket wheels or non-original TPMS sensors – the system may require a full reprogramming.
The light flashes continuously (a steady flash for more than 90 seconds at startup) – this signals a serious system fault.
You recently rotated tires or replaced a sensor and the light still won’t go out.

A Hyundai dealer or a tire shop with a TPMS scan tool can read the sensor IDs, check battery voltages, and perform a relearn or reprogramming. For more information on selecting the right diagnostic tool, check out our guide on [best OBD scanners for Hyundai vehicles] (link placeholder).

Frequently Asked Questions

Q: How long does it take the TPMS light to reset on a Hyundai i10?
A: Typically 10–20 minutes of driving above 40 km/h. If the light remains on after 30 minutes, check your tire pressures and try a manual reset.

Q: Can I reset the TPMS without the button on a 2011 Hyundai i10?
A: Yes, but only through the automatic method. Inflate tires to the correct pressure and drive at highway speeds. If that fails, locate the TPMS button under the steering column.

Q: Does disconnecting the battery reset the TPMS on a Hyundai i10?
A: No. Disconnecting the battery clears temporary memory but does not clear the TPMS fault. The light will return as soon as you drive the car.

Q: How do I know if my TPMS sensor is dying?
A: A dead sensor usually causes the light to flash at startup for about 60–90 seconds and then stay solid. You may also see a “Sensor Fault” message on the dashboard.

Q: Is it safe to drive with the TPMS light on?
A: It is safe in the short term, but you should check your tire pressure immediately. Low pressure can lead to poor handling, increased wear, and even tire failure.

Q: Where is the TPMS reset button on a 2011 Hyundai i10?
A: Look underneath the steering column, near the fuse box cover. It is a small square button with a tire icon. Some models have it inside the glovebox.

About the Author: Erwin Salarda is an Automotive Service Equipment Technician based in the Philippines, specializing in computerized automotive diagnostic equipment such as OBD scanners and wheel alignment systems. Since 2012, he has been actively providing technical support, equipment installation, troubleshooting, after-sales service, and hands-on training for automotive service equipment used by workshops and automotive professionals.

He has received specialized training from international suppliers and manufacturers, including Launch X431 in Shenzhen, China, Lawrence Engineering Company in Guangzhou, China, and 3Excel Wheel Alignment Company in Shenzhen, China. Through these trainings, he developed advanced expertise in automotive diagnostics, calibration, wheel alignment systems, and computerized automotive service technologies.

Erwin Salarda provides professional after-sales support and technical training for automotive diagnostic and wheel alignment equipment, helping clients maximize the performance and proper use of their tools and systems. His experience covers equipment setup, software updates, calibration procedures, troubleshooting, and operational guidance for automotive workshops and service centers.

With more than a decade of experience in the automotive equipment industry, Erwin Salarda continues to support automotive businesses by delivering reliable technical expertise and practical training solutions.

For inquiries and equipment purchases, please visit https://carlifterph.com/

How to Reset TPMS on Hyundai i10 (All Years) – Step-by-Step Guide